Ws2812B 8x8 16x16 led panel light



Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen
Email:jessie@witop-tech.com  phone:0086+15676178187

 Picture Show 
LED Quantity: 64
IC Type WS2812 (IC Built in LED)
Wattage: 19.2W
Pixel/m: 8*8
PCB Width: 9*9cm
Length of cable: 100mm
Working Voltage: DC 5V
PCB Color: black

Features.
1. Control IC SK6812/ws2812b  inserted in 5050 RGB LED diode , supporting numerous color-change effects .
2. White PCB and black PCB optional .
3. It comes in one piece separated by a 3Pin JST SM connector and extra Power /Ground Wires .
4. Flexible PCB material . This matrix has a thick flexible PCB backing that can
be gently bent and curved around surfaces
5. This matrix with 256 leds, you could use over 15A of current if you turn on all the LEDs on to white (which we really do not recommend because we don't think the flex PCB can handle that much current in a long time ). Try to keep the current draw at under 5A.


These are awesome 8x8 individually addressable RGB matrix panels. Composed of 8 columns x 8 rows of WS2812B (WS2812/WS211 protocol) individually addressable LEDs on a flexible PCB, these panels have 64 LEDs and they can be daisy-chained to make bigger signs or panels! You can create animations, games, or even incorporate them into a fun e-textiles project. On top of all that, thanks to its flexible backing, this LED Matrix can be bent and bowed to fit onto almost any curvy surface.

These panels require a 5V low voltage input for power which needs to be able to source a good amount of current – up to 3.8A in most uses (3.8A if all LEDs are set to bright white, which is NOT recommended). Attached to each flexible LED matrix are two 3-pin JST SM connectors and two sets of bare power cables (input / output), which provide you connections for DC5V+, COM-, DAT, and GND.

Pls note that WS2812B are a bit different than the standard WS2801 ICs, these do not use separate clock and data lines.
Learn more please contact us 

评论

发表评论

此博客中的热门博文

Ws2813 RGB Led Chip Data sheet

图片
Shenzhen Witop technology Co,.Ltd www.witop-tech.com                  Ws2813 RGB Led Chip                     Features and Benefits 1、 The control circuit and the LED share the only power source. 2、 The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel. 3、 Using the built-in signal reshaping circuit to achieve the signal waveform shaping, and no distortion of waveform of signal takes place. 4、 Built-in power-on reset and brown-out reset circuits. 5、 The gray levels of each pixel are of 256 levels, which achieves “256*256*256=16777216” full-color display, and the refresh frequency reaches to 2KHz/s. 6、 Serial cascade interface, data receiving and decoding depend on just one signal line. 7、 Dual-signal wires version, signal break-point continuous transmission. 8、 Any two point the distance more than 3m transmission signal without any increase circuit. 9、 When the refresh rate is 30fps, cascade numbers are far more tha
阅读全文

RGBW VS RGBWW RGB VS RGBW

图片
Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen Email:jessie@witop-tech.com  phone:0086+15676178187 RGBW  VS RGBWW RGBW LED strip has been around for a while now and has opened the door to previously unheard-of lighting possibilities, allowing not only a wide range of customisable colors but also the ability to cut and join any length to create totally unique shapes. In response to popular demand though, there's now a new kid on the block, RGB+WW, which adds an extra white chip into the mix. Why might you need this? Read on.. What’s the difference between RGBW and RGBWW LED strip? Standard RGBW LED strip uses a 4-in-1 LED chip made up of red, green,blue and W chips. It can produce a wide range of colors by mixing the four  and looks almost white with all  at full brightness. RGB+W+W LED strip uses either a 5-in-1 LED chip that has A Warm white chip and RGB Led, also has a White color on the right.
阅读全文

K-1000C SD card controller

图片
Email：jessie@witop-tech.com                    phone:0086+15676178187  Tel:0086+0755-23081280 WTP -K-1000C Using Manual 一、 K-1000C system features: 1000C SD Card Controller K-1000C system features: 1 、 32 to 65536 degree Gray control, Gamma correction procession handle. 2 、 Support various point, line light source, and all kinds of rules and specific shaped  h andle. 3. The controller has one output port, can support up to 512/2048 pixels(DMX lighting support   up to 512 pixels). 4 、 Play content stored in the SD card , the SD card can store up to 32 effects File, SD card   capacity support 128MB-32GB. 5 、 The controller can single set use,also multiple controllers cascade, cascade optical   isolation mode: interference, better stability, cascade distance between two controllers can   reach up to 150 meters, need to use 0.5M² pure copper power cord. 6 、 The controller support chip can lock the support IC in software, or not lock the support   IC in the software, sele
阅读全文