How to Connect the ws2813 Led strip?

Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen
Email:jessie@witop-tech.com  phone:0086+15676178187
How to Connect the ws2813 Led strip?


ws2813 led is ws2812 update version,dual-signal wires , signal break-point continuous transmission ,the ws2812b is regular addressable with one data wire, V+&V-.

first, get some features about ws2813 led strip.
Adopt international leading manufacturer’s chips high brightness width angle color consistency and stable performance Each lamp beads form a loop can be arbitrarily cut according to the needs of the length of the loop without damaging other parts Convenient to Fix and install flexible cutting operation make the construction simple ultra thin design low temperature light source make the selection for the auxiliary material more flexible on installation Energy saving high brightness low heat low energy consumption Clean and beautiful;Use DC5V to power supply more safe on using Protection Rating IP62 IP65 IP67 IP68 use range is wide Small  multi colored no radiation high shock resistance is a new generation of green high tech products.

Some Application
1.City skyline lighting villas advertising wall signs Christmas decorative landscape
2.Irregular design of body decoration shopping malls hotels nightclubs polygonal wall KTV establishments ceiling cavity design
3.Public lighting lighting schools libraries hospitals airports subway stations railway stations
4.Furniture dark groove trim door bar wine cabinet wardrobe TV cabinets etc
5.Automotive beauty body underbody wheelbarrow balanced car etc

Regular, the ws2813 we have 30led&60led&144led per meter. more than 5M/roll will be Voltage Drop.so 5M/roll is the best.

How to Connect the Ws2813led strip?

You can control WS2183 LED strips from the FastLED library.

Use the "WS2812" type and set-up the LED strip by specifying the DATA PIN.

Now connect BOTH centre pins of the strip to this pin and the strip should work.

I've been searching for this for ages and finally got my strip to work!

Like wiring




评论

发表评论

此博客中的热门博文

Ws2813 RGB Led Chip Data sheet

图片
Shenzhen Witop technology Co,.Ltd www.witop-tech.com                  Ws2813 RGB Led Chip                     Features and Benefits 1、 The control circuit and the LED share the only power source. 2、 The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel. 3、 Using the built-in signal reshaping circuit to achieve the signal waveform shaping, and no distortion of waveform of signal takes place. 4、 Built-in power-on reset and brown-out reset circuits. 5、 The gray levels of each pixel are of 256 levels, which achieves “256*256*256=16777216” full-color display, and the refresh frequency reaches to 2KHz/s. 6、 Serial cascade interface, data receiving and decoding depend on just one signal line. 7、 Dual-signal wires version, signal break-point continuous transmission. 8、 Any two point the distance more than 3m transmission signal without any increase circuit. 9、 When the refresh rate is 30fps, cascade numbers are far more tha
阅读全文

RGBW VS RGBWW RGB VS RGBW

图片
Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen Email:jessie@witop-tech.com  phone:0086+15676178187 RGBW  VS RGBWW RGBW LED strip has been around for a while now and has opened the door to previously unheard-of lighting possibilities, allowing not only a wide range of customisable colors but also the ability to cut and join any length to create totally unique shapes. In response to popular demand though, there's now a new kid on the block, RGB+WW, which adds an extra white chip into the mix. Why might you need this? Read on.. What’s the difference between RGBW and RGBWW LED strip? Standard RGBW LED strip uses a 4-in-1 LED chip made up of red, green,blue and W chips. It can produce a wide range of colors by mixing the four  and looks almost white with all  at full brightness. RGB+W+W LED strip uses either a 5-in-1 LED chip that has A Warm white chip and RGB Led, also has a White color on the right.
阅读全文

K-1000C SD card controller

图片
Email：jessie@witop-tech.com                    phone:0086+15676178187  Tel:0086+0755-23081280 WTP -K-1000C Using Manual 一、 K-1000C system features: 1000C SD Card Controller K-1000C system features: 1 、 32 to 65536 degree Gray control, Gamma correction procession handle. 2 、 Support various point, line light source, and all kinds of rules and specific shaped  h andle. 3. The controller has one output port, can support up to 512/2048 pixels(DMX lighting support   up to 512 pixels). 4 、 Play content stored in the SD card , the SD card can store up to 32 effects File, SD card   capacity support 128MB-32GB. 5 、 The controller can single set use,also multiple controllers cascade, cascade optical   isolation mode: interference, better stability, cascade distance between two controllers can   reach up to 150 meters, need to use 0.5M² pure copper power cord. 6 、 The controller support chip can lock the support IC in software, or not lock the support   IC in the software, sele
阅读全文