High CRI RA90 2216 led strip Manufacturers and Suppliers

Add:Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen
Email:jessie@witop-tech.com              Phone:0086+15676178187


high bright high lumen 2216SMD 240led led strip 

Picture show 



Description
This product is suitable for advertising signs, hotels, bars, KTV, nightclubs, bridges and other building facades and home lighting projects.

Features
  1. FPC with the best flexibility as a substrate, FPC has good electrical conductivity, heat fast, resistant to bending, can be bent into any shape
  2. Using high display light high efficiency SMD2216 led Chip
  3. The brightness of the light bar can be changed by dimming the power supply
  4. working on low-voltage DC24V power supply, the user is more secure when used
  5. Can be made of waterproof level of diversification, glue cover waterproof (IP65), all-inclusive casing waterproof (IP67), casing injection (IP68)

Installtion
Back to paste 3M glue, install the attachment customer-owned
warranty
two years warranty, non-human factors caused by product quality problems, warranty replacement
The Division reserves the right of final interpretation

Size
Specification
Item
Color
Bean angle
Lumen
Voltage
Power
WTP-H-2216X240-24V
Single color
120°
2400lm/m
DC24V
19.2W/m

Note
①Light decay parameters test the ambient temperature of 25 degrees plus or minus 3 degrees
②Note due to the particularity LED product manufacturing process technical parameters above reflect only the statistics do not necessarily correspond to the actual parameters of each product the product may differ from the actual parameters of the above parameters

Installation wiring diagram
Note
1.Please read the specifications and precautions carefully before installation
2.Please do not use nails or sharp instruments to intall led strip on the object use double sided tape or glue or wall mounted on plywood
3.Fixed led strip you can not use acidic glue it is recommended to use a neutral glue , , .
4.This product is a constant voltage DC5V make sure Power is right before installation after installation check the wiring is correct or not so that avoid the product been burned ,
5.TThis product is recommended use in parallel when the length is more than five meters the tail so be power to ensure the brightness is enough or uneven

评论

发表评论

此博客中的热门博文

Ws2813 RGB Led Chip Data sheet

图片
Shenzhen Witop technology Co,.Ltd www.witop-tech.com                  Ws2813 RGB Led Chip                     Features and Benefits 1、 The control circuit and the LED share the only power source. 2、 The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel. 3、 Using the built-in signal reshaping circuit to achieve the signal waveform shaping, and no distortion of waveform of signal takes place. 4、 Built-in power-on reset and brown-out reset circuits. 5、 The gray levels of each pixel are of 256 levels, which achieves “256*256*256=16777216” full-color display, and the refresh frequency reaches to 2KHz/s. 6、 Serial cascade interface, data receiving and decoding depend on just one signal line. 7、 Dual-signal wires version, signal break-point continuous transmission. 8、 Any two point the distance more than 3m transmission signal without any increase circuit. 9、 When the refresh rate is 30fps, cascade numbers are far more tha
阅读全文

K-1000C SD card controller

图片
Email：jessie@witop-tech.com                    phone:0086+15676178187  Tel:0086+0755-23081280 WTP -K-1000C Using Manual 一、 K-1000C system features: 1000C SD Card Controller K-1000C system features: 1 、 32 to 65536 degree Gray control, Gamma correction procession handle. 2 、 Support various point, line light source, and all kinds of rules and specific shaped  h andle. 3. The controller has one output port, can support up to 512/2048 pixels(DMX lighting support   up to 512 pixels). 4 、 Play content stored in the SD card , the SD card can store up to 32 effects File, SD card   capacity support 128MB-32GB. 5 、 The controller can single set use,also multiple controllers cascade, cascade optical   isolation mode: interference, better stability, cascade distance between two controllers can   reach up to 150 meters, need to use 0.5M² pure copper power cord. 6 、 The controller support chip can lock the support IC in software, or not lock the support   IC in the software, sele
阅读全文

RGBW VS RGBWW RGB VS RGBW

图片
Add:3/F,Building A,Jinmao Technology Park,Tangyanshan lndustrial Zone Tangkeng,Shiyan,BaoanDistrict,Shenzhen Email:jessie@witop-tech.com  phone:0086+15676178187 RGBW  VS RGBWW RGBW LED strip has been around for a while now and has opened the door to previously unheard-of lighting possibilities, allowing not only a wide range of customisable colors but also the ability to cut and join any length to create totally unique shapes. In response to popular demand though, there's now a new kid on the block, RGB+WW, which adds an extra white chip into the mix. Why might you need this? Read on.. What’s the difference between RGBW and RGBWW LED strip? Standard RGBW LED strip uses a 4-in-1 LED chip made up of red, green,blue and W chips. It can produce a wide range of colors by mixing the four  and looks almost white with all  at full brightness. RGB+W+W LED strip uses either a 5-in-1 LED chip that has A Warm white chip and RGB Led, also has a White color on the right.
阅读全文