K-8000D SD Card LED Controller 8 Ports Output Support 512

K-8000D Operation Manual

一、K-8000D Feature：

    1、32—65536 gray level control，Gamma correction processing 。

2、Support each regular and  anomalous  mapping

3、The controller have 8 channels，each channel support 512 pixel (Max)。

4、Controller support cascade connection ，wire length between each controller can   achieve distances of up to 200m (max) ，

5、K-8000D could support 30pcs different pattern .

备注：Remark:

1.Please contact sales or technical support person to know the details when you need to use the global wireless GPS

synchronization,

channel distributor and timing play.(备注：1、需要使用全球无线 GPS 同步、控台通道分配器和定时播放的时候请联系

销售人员或者技术支持了解详细情况)

二、Support chip：

 Standard DMX Protocol 250Kbps

Standard DMX Protocol 250Kbps

UCS1903 1909 1912 (High Speed)

Note：Single IC only need connect A and GND

三、right side view：

四、 丝印含义：

     The key implication ：

Key	implication
CHIP	choose IC Type
MODE	Switch program file/ code writing
SPEED+	Speed +	Press SPEED+ and SPEED- in the same time，Program file  Loop Mode
SPEED-	Speed -

VCC	DC5V input
POWER	Power light
ERROR	Lamp Error Detection
SD卡/SD CARD	SD card slot

    

Output signal（485 signal）：

A	signal+
B	signal-
GND	Ground
ADD	Write code line

     

     

五、写码过程：The process of write code

接线方式：

      启动状态The state of startup

        Chip00—03表示支持的IC  Chip00—03 The IC of support(表示支持的 IC)

        00——标准DMX 250KB  00——Standard DMX 250KB(标准 DMX 250KB)

        01——标准DMX 500KB  01——Standard DMX 500KB(标准 DMX 500KB)

        02——UCS窗帘灯      02——UCS curtain lamp(UCS 窗帘灯)

        03——UCS1903

       

Chip04—06 The IC of write code(表示写码的 IC)

04——UCS512A write code (UCS512A 写码)

05——WS2821 write code (WS2821 写码)

06——Temporary is empty (暂时为空)

Ch.03

Represent 3 channel（表示 3 通道）       

Note: Long press “Mode” 8 second, can UCS512 write code directly. The mode of write code is default 3 channels.

(注：长按 Mode 8 秒可直接 UCS512 写码，写码模式为默认 3 通道)

六、加密词汇解释 The explanation of encrypted vocabulary

Password is OK	密码正常！
Num	剩余开机次数
Password exist	密码已经存在
Can't repeated	不能重复加密
Set Password OK	设置密码成功
Clear Pwd OK	清除密码成功
Pwd not right	密码不正确
No Password	密码不存在
Has expired! Contact factory	密码已过期，请联系工厂！

七、接线方式The mode of connection

Remarks: 1. If the distance between controller to LEDs over 50meters, suggested to add a repeater.

2. If couldn’t pull the synchronization signal wires of the controller between two buildings, it is recommended to use global wireless

GPS synchronization module.

The details please refer to the synchronization scheme of GPS synchronization module.

3. The wires of transmission signals are recommended to use good quality HSYV or RVVP shielded wire to transmit.

(备注：1、如控制器到灯的距离超过 50 米时建议加一个差分中继器。

2、如两栋大楼之间的无法拉控制器的同步信号线，建议使用全球无线 GPS 同步模块，详情请查阅后面的 GPS 同步模块同步方案。

3、传输信号的线材建议使用质量好的超五类网或 RVVP 屏蔽线进行传输)

八、具体参数：Specific parameters

   SD card：

         Type：SD card

          capacity：128MB—2GB

          Format：FAT

          File Format：*.led

   Physical data ：

         Working temperature ：-30℃—85℃

          VCC：DC5V

         Power：3W

     GW：0.8Kg

九、注意事项：

     1.Before coping the files to the SD card, must to format the SD card first. Pay attention, it’s must to format the SD card

before coping files every time.

2.SD card must formatted as “ FAT” format.

( 1、将文件拷贝到 SD 卡之前，必须先对 SD 卡格式化，注意是每次拷贝之前都要格式化。2、SD 卡必须要格式化

成“FAT“格式.)

     Remark: The SD card in controller can not hot-plug or hot-swap, must disconnect the power of the controller first.

(备注：控制器上的 SD 卡不可以热插拔，即每次插拔 SD 卡时，必须先断开控制器的电源)